Chlorinated rubber, isoprene = 2-methyl-1,3-butadiene, powder, chlorinated rubber, Parlon, Pergut

Flame sootorCarbon Black / Carbon Black / Lamp Black is produced by burning hydrocarbons with reduced oxygen supply. The flame black powder we offer is typically nanoscale. Among other things, it is also suitable as an extremely opaque black pigment.  This is a prilled version. This means that significantly less dust is created during handling and the material is easier to dose andIn addition, the environmental impact is significantly reduced.Possible applications: Additive in polymers Conductive paints (ESD applications) Polymer-based energy storage Black pigment (e.g. toner) Flame retardant coatings and much more. Chemical/physical examination: Average particle size: 95nm (0.095µm) - based on primary particlesResidue on 45µm sieve: 4ppm Toluene extractable components (DIN 53553): 0.010% CAS No.: 1333-86-4 Variety: 101 Carbon min.: 99.9% Opacity (ISO 787/16 & 24): 26.0% (ITRB) Blackness (DIN 55979): 210 PH value: 7.5 Tamping density: 260 g/l Dibutyl phthalate absorption: 0.118 dm³/100g

Flame sootorCarbon Black / Carbon Black / Lamp Black is produced by burning hydrocarbons with reduced oxygen supply. The flame black powder we offer is typically nanoscale. Among other things, it is also suitable as an extremely opaque black pigment. Possible applications: Additive in polymers Conductive paints (ESD applications) Polymer-based energy storage Black pigment (e.g. toner) Flame retardant coatings and much more. Chemical/physical examination: Average particle size: 95nm (0.095µm) - based on primary particlesResidue on 45µm sieve: 4ppm Toluene extractable components (DIN 53553): 0.010% CAS No.: 1333-86-4 Variety: 101 Carbon min.: 99.9% Opacity (ISO 787/16 & 24): 26.0% (ITRB) Blackness (DIN 55979): 210 PH value: 7.5 Tamping density: 260 g/l Dibutyl phthalate absorption: 0.118 dm³/100g" ThisDextrin (canary dextrin) will be outCornstarchwon. The starch is mixed with steam or catalytically active acid under increased temperature and pressure. This converts the otherwise insoluble starch into awater soluble product, which mainly asbinderapplies. A commonly known use is thisWet adhesive coating (also called gumming) of postage stamps and kraft paper tapes. However, it is also used as a food additive or as a binding agent in pharmaceuticals. The material isvery soluble in waterand binds even at low moisture levels. There are now many dextrin-based artists' colors on the market (mixture of dextrin and pigment, as well as water). Product dataCAS No.: 9004-53-9 Average particle size: 17.50 µmHumidity: max. 10% [MCL 002B]pH value: 2.5 - 4.0 [20% solution]RVA viscosity: 960-2040 mPa*s [MCL 106T]Insoluble components: max. 2% [MCL 340A]Reduced sugar: max. 4.2% [MCL 050A]Bulk density: approx. 0.55 kg/dm³ [MCL 095A]

This coarser silicon powder is mechanically produced from pure starting material with at least 98.0% silicon. Due to its coarser particle size, this powder is better suited for melting and foundry applications.Chemical analysis (typical values):Si: > 98.0%Fe: < 1.0%Particle size distribution (typical values):D90 190 µmD50 125 µmD10 75 µm

This Coarse silicon granules are mechanically obtained from pure starting material with at least 99.0% silicon purity. Due to its large particle size, this powder is ideally suited for melting and foundry applications. Chemical analysis (typical values): Si: > 99.0% Fe: 3814 ppmw Al: 297 ppmwApprox.: 10 ppmwTi: 110 ppmwP: 39 ppmwCu: 15 ppmwCr: 43 ppmwK: 1.2 ppmwV: 10 ppmwNi: 15 ppmwNa: 0.4ppmwParticle size distribution (typical values): < 2000 µm: 0.10% 200 - 2000µm: 99.9% < 200µm: 0.0%

This silicon powder is mechanically produced from high-purity starting material with at least 99.0% silicon. The very small particle size gives the material increased reactivity and sintering activity, making it particularly interesting for ignition systems, gas generators, technical ceramics, and high-temperature applications. It is also ideally suited for the production of silicon nitride or silicon carbide. Chemical analysis (typical values): Si: > 99.0% Fe: approx. 0.4% Al: approx. 0.2% Approx.: approx. 0.06% Particle size distribution (typical values): D90 4.0 µm D50 2.0 µm D10 0.6 µmSignal word: ATTENTION!Hazard statements H228: Flammable solidPrecautionary statements P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P402+P404: Store in a closed container in a dry place.

This Brass powder ist vor allem als Füllstoff in Kunststoffsystemen und wegen seiner unregelmäßigen Partikel auch als Sinterpulver suitable.  Typical chemical and physical specifications:Purity of the base metal: 99,9 % Alloy: >69,5% Cu, >30,0% Zn, Pb rest >150micron 0,0%150-104µm 15%104-74µm   15%74-44µm     25%<44µm       45%CAS No.: 7440-50-8 Signal word: WARNING! Hazard statements H411 - Toxic to aquatic life with long-lasting effects. Precautionary statements P273: Avoid release to the environment. P501: Dispose of contents/container at an approved waste disposal facility.

This silicon powder is mechanically produced from high-purity starting material with at least 99.9% silicon. The very small particle size gives the material increased reactivity and sintering activity, making it particularly interesting for ignition systems, gas generators, technical ceramics, and high-temperature applications. It is also ideally suited for the production of silicon nitride or silicon carbide. Chemical analysis (typical values): Si: > 99.9% Al: 351.3 ppmw Ca: 70.9 ppmw Fe: 75.4 ppmw Ti: 5.1 ppmw P: 1.8 ppmw Cu: 16.2 ppmw Cr: 2.6 ppmw K: 6.9 ppmw V: 0.1 ppmw Ni: 1.5 ppmw Na: 14.7 ppmw Particle size distribution (typical values): D90 7.92 µm D50 4.16 µm D10 1.33 µmSignal word: ATTENTION! Hazard statements  H228: Flammable solid  Precautionary statements  P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P402+P404: Store in a closed container in a dry place.

Formula: Mo CAS No.:7439-98-7 Tapped density: 3,1g/cm³ Average particle size: 5µm F.S.S.S Chemical characterization Mo: min. 99,90 %C: 0,002 %O: 0,026 %Fe: 0,002 %

Carbon: 85 - 90% Density: 253 g/dm³Humidity: 0.37%Sieve residue on 71µm sieve: max. 15.0%Sieve passage 71µm sieve: min. 85.0% Typical applications:  Dry lubricant (replacement for molybdenum disulfide) Conductive paints and plasticsAdditive against static charge metallurgy Flame retardants

Carbon: 88.70%Ash: <0.5%Sieve residueon 315µm: 5.5%on 200µm: 39.2%on 160µm: 31.3%on 100µm: 18.5%on 71µm: 1.8%

This silicon powder is mechanically extracted from high-purity raw material with at least 99.0% silicon . The small particle size gives the material increased reactivity and sintering activity, making it particularly interesting for the fields of ignition systems, gas generators, technical ceramics or also high-temperature applications. Chemical analysis (typical values): Si: > 99.0% Fe: 3814 ppmw Al: 297 ppmwCa.: 10 ppmwTi: 110 ppmwP: 39 ppmwCu: 15 ppmwCr: 43 ppmwK: 1.2 ppmwV: 10 ppmwNi: 15 ppmwNa: 0.4 ppmwParticle size distribution (typical values): d10 6µmd50 21µm d90 47µm Signal word: WARNING! Hazard warnings H228: Flammable solid Safety instructions P210: Keep away from heat, hot surfaces, sparks, open flames, and other sources of ignition. No smoking. P402+P404: Store in a closed container in a dry place.

This copper powder is produced by air atomisation . This process creates irregular and partly spherical primary particles. Powders obtained by this process show a higher bulk and tap density compared to dendritic powders.Further typical fields of application:Antifouling coatingsFriction liningsPlastics engineering (as a filler)Soldering technologyCatalyst (chem.)Silver production (precipitation of silver in silver nitrate solution)Antibacterial / antiviral coatingsPaint coatings (so-called "piss paintings") -> ATTENTION: This powder is not suitable as a pigment. For this purpose, please use our flake-shaped powdersTypical chemical / physical specifications:Copper: min. 99.5 %Particle size distribution (typical)D10 12.0 - 17.0 μm D50 22.0 - 31.0 μm D90 32.0 - 43.0 μmBulk density: 4.6 to 4.9 g/cm³CAS No.: 7440-50-8 Signal word: WARNING! Hazard statements:H412 Harmful to aquatic life with long lasting effects.Precautionary statements:P273 Avoid release to the environment.P391 Collect spillage. "

This copper powder is produced by water atomisation . This results in irregularly shaped primary particles with increased interlocking effect. However, this means that the powder is only suitable to a limited extent for AM processes. Compared to the air-atomised variant, which is also available from us, grade "LD" has an approximately 30% lower bulk density.Further typical fields of application:Antifouling coatingsFriction liningsSintered componentsPlastics engineering (as a filler)Soldering technologyCatalyst (chem.)Silver production (precipitation of silver in silver nitrate solution)Antibacterial / antiviral coatingsPaint coatings (so-called "piss paintings") -> WARNING: This powder is not suitable as a pigment. For this purpose, please use our flake-shaped powdersTypical chemical / physical specifications:Copper: min. 99.6 %Oxygen: max. 0.2 %Particle size distribution (typical)> 149 µm (100 mesh): 0.0 %> 105 µm (140 mesh): 1.6 %> 44 µm (325 mesh): 35.0 %Bulk density: 3.0 - 3.6 g/cm³CAS No.: 7440-50-8 Signal word: WARNING! Hazard statements:H412 Harmful to aquatic life with long lasting effects.Precautionary statements:P273 Avoid release to the environment.P391 Collect spillage.

This copper powder is obtained electrolytically . This process produces very pure powders that have a dendritic particle shape with a small primary particle size. This makes them particularly suitable for sintering applications, as the branched particles form a good positive fit with each other and thus promote the strength of the green compact. Other typical areas of application:Antifouling coatingsFriction liningsPlastics technologySoldering technologyLubricantsCatalyst (chemical)Antibacterial / antiviral coatingsPaints (so-called "Pisspaintings")Typical Chemical / physical specifications:ISO 4497:> 63µm: max. 3.0% > 45µm: max. 10.0% < 45µm: min. 87.0 % Fill density (ISO 3923/1): 1.4 to 1.6 g/cm³Spec. Fisher Surface: 1200 cm²/gOxygen: 0.15%Extracted from 99.9 percent copperCAS No.: 7440-50-8Signal word: ATTENTION! Hazard statements:H400 Very toxic to aquatic life.H412 Harmful to aquatic life with long lasting effects.Precautionary statements:P273 Avoid release to the environment.P391 Collect spillage.

This copper powthe is specially designed for optical and functional applicationsdeveloped and manufactured worden. This is pure copper, which has been stabilized with 1,5 % oleic acid. In Kunststoffverarbeitung produces outstanding effects in HDPE, LDPE,ABS othe gar PVC. In this context should during the Fertigung of Masterbatches care must be taken to ensure that the powthe nur geringstmöglichen Scherkräften and Verweildauern during hohen Temperaturen ausgesetzt wird. Beide Faktoren könnten sonst the optical Endergebnis negativ beeinflussen. Ebenfalls is this powthe bestens auf den Einsatz in paints/coatings/2K-Harz and screen-printing processes abgestimmt. A ratio of 5/100 (Pigment/Bindemittel) is for ein optisch high-quality result . This produces an impressive copper-metallic effect - the surface sieht anschließend wie ein polished copper sheet aus. Bitte beachten Sie during the processing: screen printing: Maschenweite should drei mal größer als the D90-Wert des powders sein. Aerosol spray cans: Der D90-Wert des powders sollten mindestens drei mal kleiner als the Düsendurchmesser sein. Lacke/paints: Mechanische Einflüsse durch sehr schnell drehende agitators avoid. Dies würde the Partikel beschädigen and den Metallic-Effekt zerstören. Typische chemical and physical Spezifikationen:Purity des Ausgangsmetalls: 99,9 %Laser diffraction: D10 2,75µmLaser diffraction: D50 6,75µmLaser diffraction: D90 16µmBulk density: ca. 0,90 g/cm³Hiding power: ca. 9000 cm³/gAcetone-soluble constituents: 1,5 % (oleic acid)CAS No.: 7440-50-8 Signal word: Danger! Dangerenhinweise H228 - Flammable solid. H302 - Harmful if swallowed H400 - Sehr toxic for aquatic organisms H411 - Toxic for aquatic organisms with long-lasting effects. Precautionary statements P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P273 - release in the Umwelt avoid. P301+P310 - If swallowed: Sofort Giftinformationszentrum, Arzt anrufen. P330 - Rinse mouth P370+P378 - In case of fire: Metallbrandpulver/Zement/Sand zum Löschen use

This copper powthe is specially designed for optical and functional applicationsdeveloped and manufactured worden. This is pure copper, which has been stabilized with 1,5 % oleic acid. In Kunststoffverarbeitung produces outstanding effects in HDPE, LDPE,ABS othe gar PVC. In this context should during the Fertigung of Masterbatches care must be taken to ensure that the powthe nur geringstmöglichen Scherkräften and Verweildauern during hohen Temperaturen ausgesetzt wird. Beide Faktoren könnten sonst the optical Endergebnis negativ beeinflussen. Ebenfalls is this powthe bestens auf den Einsatz in paints/coatings/2K-Harz and screen-printing processes abgestimmt. A ratio of 5/100 (Pigment/Bindemittel) is for ein optisch high-quality result . This produces an impressive copper-metallic effect - the surface sieht anschließend wie ein polished copper sheet aus. Bitte beachten Sie during the processing: screen printing: Maschenweite should drei mal größer als the D90-Wert des powders sein. Aerosol spray cans: Der D90-Wert des powders sollten mindestens drei mal kleiner als the Düsendurchmesser sein. Lacke/paints: Mechanische Einflüsse durch sehr schnell drehende agitators avoid. Dies würde the Partikel beschädigen and den Metallic-Effekt zerstören. Typische chemical and physical Spezifikationen:Purity des Ausgangsmetalls: 99,9 %Laser diffraction: D10 2,75µmLaser diffraction: D50 9µmLaser diffraction: D90 20,5µmBulk density: ca. 0,95 g/cm³Hiding power: ca. 7500 cm³/gAcetone-soluble constituents: 1,5 % (oleic acid)CAS No.: 7440-50-8 Signal word: Danger! Dangerenhinweise H228 - Flammable solid. H302 - Harmful if swallowed H400 - Sehr toxic for aquatic organisms H411 - Toxic for aquatic organisms with long-lasting effects. Precautionary statements P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P273 - release in the Umwelt avoid. P301+P310 - If swallowed: Sofort Giftinformationszentrum, Arzt anrufen. P330 - Rinse mouth P370+P378 - In case of fire: Metallbrandpulver/Zement/Sand zum Löschen use

This silicon powder is mechanicallyproduced from high-purity starting material with at least 99.0% silicon. The small particle size gives the material increased reactivity and sintering activity, making it particularly interesting for applications such as ignition systems, gas generators, technical ceramics, and high-temperature applications. Chemical analysis (typical values): Si: > 99.0% Al: 125 ppmw Ca: 69 ppmw Fe: 935 ppmw Ti: 189 ppmw P: 26 ppmw Cu: 63 ppmw Cr: 80 ppmw K: 48 ppmw V: 97 ppmw Ni: 45 ppmw Na: 39 ppmw Particle size distribution (typical values):> 45µm: 15.0%10-45µm: 45.0%1-10µm: 35.0%< 1µm: 3.0%Signal word: ATTENTION! Hazard statements  H228: Flammable solid  Precautionary statements  P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P402+P404: Store in a closed container in a dry place.

This aluminum powder is produced in Europe by atomizing it with air. It is characterized by irregular primary particles and thus good green strength.Preferred areas of application Filler in polymer processing (2K systems, filler) Adjusting thermal conductivity in polymers and/or increasing strength Chemical reducing agent / gas generators Pyrotechnics Not a hazardous material in the sense of transport regulations Particle shape: irregular, spattered Made from primary aluminum CAS No.: 7429-90-5 Typical analysis values Al: min. 99.7% Fe: 0.13% Si: 0.03% Cu: max. 0.003% Granulometry D10 14.6 μm D50 47.5 μm D90 129 μm

This aluminum powder is produced in Europe via atomization with air. It is characterized by irregular primary particles.Preferred areas of applicationFiller in polymer processing (2K systems, filler)Adjusting thermal conductivity in polymers and/or increasing strengthChemical reducing agent / Gas generatorsMetallurgyFiltersPyrotechnicsNot dangerous goods within the meaning of the transport regulationsPurity: 96.9% (Al)Particle shape: irregular, spattery Made from primary aluminumGranulometry: >450µm:   0.4%< 250µm: 8.80% Bulk density: 0.940 g/cm³CAS No.: 7429-90-5

This aluminum powder is produced in Europe via atomization with air. It is characterized by irregular primary particles.Preferred Areas of applicationFiller in polymer processing (2K systems, filler)Adjusting thermal conductivity in polymers and/or increasing strengthChemical reducing agent / gas generatorMetallurgyFiltersPyrotechnicsNot classified as dangerous goods under transport regulationsPurity: 96.9% (Al)Particle shape: irregular, spatter-like Made of primary aluminumGranulometry: > 2000 µm:   9.4  %< 500 µm: 0.0 % Bulk density: 0.805 g/cm³CAS No.: 7429-90-5

This brass powder has been specifically manufactured for optical and functional applications and stands out due to its outstanding brilliance. With a medium to coarse particle size, it provides good coverage. This is a special alloy consisting primarily of copper and a small proportion of zinc. The alloy composition and the thermal treatment applied during production give this powder a brownish metallic sheen: the so-called Antique Gold finish!In plastic processing, it achieves outstanding effects in HDPE, LDPE, ABS, and even PVC. Especially in this context, care should be taken during the production of masterbatches to ensure that the powder is exposed to only minimal shear forces and residence times at high temperatures. Otherwise, both factors could negatively affect the final visual result. This powder is also perfectly suited for use in paints/coatings/2K resin and screen-printing processes. Even a ratio of 5/100 (pigment/binder) is sufficient to achieve a visually high-quality result. You will obtain an impressive copper-metallic effect – the surface will subsequently resemble polished and reflective copper sheet metal. Please observe the following during processing: Screen printing: The mesh size should be three times larger than the D90 value of the powder. Aerosol spray cans: The D90 value of the powder should be at least three times smaller than the nozzle diameter. Paints/coatings: Avoid mechanical stress caused by very high-speed mixers. This would damage the particles and destroy the metallic effect. Typical chemical and physical specifications:Purity of base metals: 99.9% (copper), 99.95% (zinc)Color tone: Copper / Antique GoldLaser diffraction: D50 32 - 38 µm (typical)Bulk density: approx. 0.95 g/cm³Covering capacity: approx. 3200 cm³/gAcetone-soluble components: < 2.0%CAS No.: 7440-50-8 (Copper), 7440-66-6 (Zinc) Signal word: WARNING! Hazard statements H400 - Very toxic to aquatic life. H411 - Toxic to aquatic life with long lasting effects. Precautionary statements P273 - Avoid release to the environment. P301+P310 - IF SWALLOWED: Immediately call a POISON CENTER/doctor. P330 - Rinse mouth. P370+P378 - In case of fire: Use metal fire powder/cement/sand to extinguish.

This brass powder is specially manufactured for optical and functional applications. It is coated with 1.5 % oleic acid, which stabilizes it. In plastic processing, it delivers outstanding effects with HDPE, LDPE, ABS, or even PVC. When producing masterbatches, special care must be taken to minimize shear forces and exposure to high temperatures. Otherwise, both factors could negatively impact the final optical result. This powder is also ideal for use in paints, coatings, 2K resins, and screen printing. A pigment-to-binder ratio of 5/100 is sufficient for an optically high-quality finish. The result is an impressive gold-metallic effect, giving the surface the appearance of polished brass sheet. Processing instructions: Screen printing: Mesh size should be at least three times larger than the powder’s D90 value. Aerosol spray cans: The powder’s D90 value must be at least three times smaller than the nozzle diameter. Paints/coatings: Avoid high-speed agitators, as mechanical stress could damage the particles and diminish the metallic effect. Typical chemical and physical specifications: Base metal purity: 99.9 % Alloy composition: ~70 % Cu, 30 % zinc Shade: rich gold Laser diffraction: D10 18.5 µm | D50 42.8 µm | D90 84.0 µm Bulk density: ~0.95 g/cm³ Hiding power: ~2600 cm²/g Acetone-soluble components: 1.5 % (oleic acid) CAS No.: 7440-50-8 Signal word: WARNING! Hazard statements H400 – Very toxic to aquatic life H411 – Toxic to aquatic life with long-lasting effects. Precautionary statements P210 – Keep away from heat, sparks, open flames, and other ignition sources. No smoking. P273 – Avoid release to the environment. P370+P378 – In case of fire: Use metal fire-extinguishing powder, sand, or cement to extinguish.

This Brass powder ist speziell für optische und funktionelle Anwendungen hergestellt worden. Es wurde 1,5 % stabilized with 1.5% oleic acid.In der plastics processing erzielt es herausragende Effekte bei HDPE, LDPE,ABS oder gar PVC. Gerade in diesem Bezug sollte bei der Fertigung von masterbatches darauf geachtet werden, dass das Pulver nur geringstmöglichen Scherkräften und Verweildauern bei hohen Temperaturen ausgesetzt wird. Beide Faktoren könnten sonst das optische Endergebnis negativ beeinflussen. Ebenfalls ist dieses Pulver bestens auf den Einsatz in Farben/Lacken/2K-Harz und screen-printingverfahren abgestimmt. Bereits ein Verhältnis von 5/100 (Pigment/Bindemittel) ist für ein optisch hochwertiges Ergebnis ausreichend. Sie erhalten einen beeindruckenden gold-metallic effect - die Oberfläche sieht anschließend wie ein polished brass sheet aus. Please observe the following during processing: screen-printing: The mesh size should be three times larger than the powder D90 value. aerosol spray cans: The powder D90 value should be at least three times smaller than the nozzle diameter. coatings/paints: Avoid mechanical stress from very fast-running agitators. This would damage the particles and destroy the metallic effect. Typical chemical and physical specifications:Purity of the base metal: 99,9 %Colour shade: BleichgoldLaser diffraction: D10 15,5 µmLaser diffraction: D50 40,5 µmLaser diffraction: D90 79, 0 µmBulk density: ca. 0,95 g/cm³Hiding power: ca. 3200 cm³/gAcetone-soluble constituents: 1,5 % (Ölsäure)CAS No.: 7440-50-8 Signal word: WARNING! Hazard statementsH400 - Very toxic to aquatic life H411 - Toxic to aquatic life with long-lasting effects. Precautionary statements P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P273 - Avoid release to the environment.P370+P378 - In case of fire: Use metal fire powder, cement or sand for extinction

This Brass powder ist speziell für optische und funktionelle Anwendungen hergestellt worden. Es wurde 1,5 % stabilized with 1.5% oleic acid.In der plastics processing erzielt es herausragende Effekte bei HDPE, LDPE,ABS oder gar PVC. Gerade in diesem Bezug sollte bei der Fertigung von masterbatches darauf geachtet werden, dass das Pulver nur geringstmöglichen Scherkräften und Verweildauern bei hohen Temperaturen ausgesetzt wird. Beide Faktoren könnten sonst das optische Endergebnis negativ beeinflussen. Ebenfalls ist dieses Pulver bestens auf den Einsatz in Farben/Lacken/2K-Harz und screen-printingverfahren abgestimmt. Bereits ein Verhältnis von 5/100 (Pigment/Bindemittel) ist für ein optisch hochwertiges Ergebnis ausreichend. Sie erhalten einen beeindruckenden gold-metallic effect - die Oberfläche sieht anschließend wie ein polished brass sheet aus. Please observe the following during processing: screen-printing: The mesh size should be three times larger than the powder D90 value. aerosol spray cans: The powder D90 value should be at least three times smaller than the nozzle diameter. coatings/paints: Avoid mechanical stress from very fast-running agitators. This would damage the particles and destroy the metallic effect. Typical chemical and physical specifications:Purity of the base metal: 99,9 %Colour shade: ReichgoldLaser diffraction: D10 2,75µmLaser diffraction: D50 9µmLaser diffraction: D90 20,5µmBulk density: ca. 0,95 g/cm³Hiding power: ca. 7500 cm³/gAcetone-soluble constituents: 1,5 % (Ölsäure)CAS No.: 7440-50-8 Signal word: Danger! Hazard statements H228 - Flammable solid. H302 - Harmful if swallowed H400 - Very toxic to aquatic life H411 - Toxic to aquatic life with long-lasting effects. Precautionary statements P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P273 - Avoid release to the environment. P301+P310 - IF SWALLOWED: Immediately call a POISON CENTER or doctor. P330 - Rinse mouth P370+P378 - In case of fire: Use metal fire powder, cement or sand for extinction